Vici 340 Dynacalibrator Manual do Utilizador Página 33
- Página / 44
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
29
Configuration 2
Pump P1 (Figure 7) draws gas in through the supply inlet on the back panel
and delivers it to accumulator AC1. The accumulator smoothes out flow fluctua-
tions generated by the pumping action and provides a port for releasing pump
backpressure through pressure relief valve RV1, set at 5 psig. The output of the
accumulator is passed through 5-micron filter F1, and split by the tee into carrier
and dilution streams.
Advanced Theory of Operation
Figure 7: Diagram of Configuration 2
Configuration 3
In this configuration (Figure 8), Pump P1 draws gas in through the supply
inlet on the back panel and delivers it to accumulator AC1. The accumulator
smoothes out flow fluctuations generated by the pumping action and provides
a port for releasing pump backpressure through pressure relief valve RV1, set at
5 psig. The output of the accumulator is passed through filter F1, which removes
particulates larger than 5 microns. The tee at the output of the filter splits the
supply into carrier and dilution streams. The carrier stream is plumbed to the
carrier outlet on the back panel, which must be plugged if an external carrier
supply is used. This port can be connected through external scrubbing media
(filters, driers, etc.) or simply looped to the carrier inlet port. Filter F2 removes
particulates larger than 5 microns from the carrier stream. The dilution stream
output of the tee is simply passed through F1, a 5 micron filter.
Configuration 4
Input configuration 4 is shown in Figure 9. Pump P1 draws gas in through
the supply inlet on the back panel and delivers it to accumu lator AC1. The
accumulator smoothes out flow fluctuations generated by the pumping action
and provides a port for releasing pump backpressure through pressure relief
valve RV1, set at 5 psig. The output of the accumulator is passed through filter
F2, which removes particulates larger than 5 microns. The tee at the output of
the filter splits the supply into carrier and dilution streams. The dilution stream is
plumbed to the back panel dilution outlet, which must be plugged if an external
dilution supply is used. This port can be connected through external scrubbing
media (filters, driers, etc.) or simply looped to the dilution inlet port. Filter F1
removes particulates larger than 5 microns from the dilution stream. The carrier
stream output of the tee is passed through 5-micron filter F2.
©
§
- Dynacalibrator 1
- Model 340 1
- Instruction Manual 1
- Symbols used in this document 2
- Table of Contents 3
- Introduction 5
- Input Configurations 8
- Rack Mount Options 8
- Special Customer Options 8
- Specifications 9
- Getting Started 10
- Concealed Damage 11
- Unit Location 12
- Rear Panel Connections 13
- Carrier/Dilution Inlets 14
- Overflow and Chamber Vents 15
- Bypass Loops 15
- 17
- 17
- Calculations 18
- Initial Power-Up 19
- Verifying Operation 22
- Serial Port Communication 24
- Entering Commands 28
- Analyzer Calibration 29
- Shutdown Procedure 30
- Advanced Theory of Operation 31
- Configuration 0 32
- Configuration 1 32
- Configuration 2 33
- Configuration 3 33
- Configuration 4 33
- Configuration 5 35
- Electrical Description 36
- Maintenance 37
- Carrier Flow Rate Verification 38
- Troubleshooting 40
- Other Pneumatic Issues 42
- Model Number Breakdown 43
- Warranty 44
Manuais e produtos relacionados com Instrumentos de medida Vici 340 Dynacalibrator
(44 páginas)Kenwood Electronics Sistemi per home cinema manuali utente
La lista di Kenwood Electronics Sistemi per home cinema prodotti contiene 1 manuali utenti per 1 modelli. Tutte le guide utenti pdf sono disponibili per essere scaricate o visionate online.
Comentários a estes Manuais